Menu

6' Easy Rider Recycled Rubber Speed Bump (G26111)

 
 
 
 
$129.98
SKU: G26111
Minimum Quantity: 12
: Online shipping not available. ADD ITEM TO CART and Request Quote
Qty:
Installation Hardware:
6' Easy Rider Recycled Rubber Speed Bump (G26111)
 
Dimensions:
(L) 6' x (W) 12" x (H) 2 1⁄4" - 51 lb.
 
**Hardware NOT included unless picked when ordering.  Each 6' Speed Bump has 4 holes for hardware installation. A SET of hardware equals qty 4 peices of hardware.
 
Image: End Caps not included
 
Lead Time:  1-3 weeks before shipment.  These items are "Built to Order".

 

WARNING: This product can expose you to chemicals including Arsenic, Cobalt, Cadmium, Lead, Chromium, Nickel Compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm.  For more information go to www.P65Warnings.ca.gov.

 
The Easy Rider® rubber speed bump reduces vehicle speeds making parking lots safer for pedestrians and motorists. Constructed from 100% recycled tires, GNR speed bumps are preformed to implement immediate installation. The Easy Rider's flexible design conforms to the contour of virtually any road surface.
 
Features:
Molded highly reflective tape ensures that the speed bumps are visible even on a dark night. Cat's eye reflectors further enhance visibility to alert drivers well in advance. The bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping.
 
Easy Rider® speed bumps are the ideal maintenance-free parking lot solution. In addition to enhancing parking lot safety, the bumps can lower insurance premiums for lot owners. 
 
The Easy Rider® is available in 4' and 6' lengths.  End caps can be added to protect the speed bump ends and vehicles. GNR rubber speed bumps are covered by a 3 year warranty; 1 year on the tape (under normal use).
 
Easy Rider® Speed Bumps are:
 
Made of 100% recycled rubber
Long lasting and cost efficient
Reduces speed to 2-5 mph
High visibility at night
Simple installation
Product can be installed in sections to create varying lengths
Will not warp, crack, chip or rot
Can be installed on any road surface
Resistant to ultraviolet light, moisture, oil, and extreme temperatures
Temporary or permanent installation - Relocatable when resurfacing / maintaining road surfaces; products can be stored and re-used 
Channeled bottom for cabling and piping
Lowers insurance premiums for lot owners
Maintenance free
Warranty: 3 years on the product; 1 year on the tape (under normal use)
Applications:
 
Used for the following situations:
 
Safety of pedestrian and vehicle traffic requires improvement
To further support and reinforce stop signs in parking lots
High risk of accidents on residential streets and in parking lots need to be reduced
Permanent or temporary lowering speed of motor vehicles is required
Only temporary installation is allowed or required
Installation on surfaces where only flexible rubber speed bumps may fully conform to the curvature of the road
roduct description:
1. Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer 
2. Physical properties of the rubber composite: 
a. Density 0.6 oz/cu in (ASTM C642) 
b. Durometer Hardness 70A ± 7 (ASTM D2240) 
c. Tensile Strength 300 psi (ASTM D412) 
d. Compression deformation 7% at 70psi, 68°F (ASTM D575) 
e. Brittleness at Low temperature: -40°F (ASTM D746) 
f. Freeze and thaw when exposed to de-icing chemicals no loss after 50 cycles (ASTM C672) 
g. Coefficient of thermal expansion: 8 x10-5 in/in/°F (ASTM C531) 
h. Weathering 70 hours at 158°F (ASTM D573) 
- hardness retained 100% (± 5%) 
- compressive strength 100% (± 5%) 
- tensile strength 100% (± 5%) 
- elongation retained 100% (± 5%) 
 
3. Available models: 6', 4' long 
4. Finishing: Black recycled rubber composite with yellow, durable and reflective, in-molded pavement marking tape
 
Components:
 
a)100% recycled rubber from car and truck tires (NR, SBR) 
b)polyurethane prepolymer 
c)cat's eyes reflectors 
d) yellow, durable and reflective in-molded pavement marking tape
 
Warranty:
 
3 years on the rubber; 1 year on the tape (under normal use) installed as per the manufacturer's installation instructions.
 
 
Installation Guide:
Components:
Easy Rider® speed bumps
1/2" (diameter), 14" (length) rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR
 
What You Need:
Gloves, safety glasses
Traffic cones, drums or barricades for securing the site
Mallet
Heavy duty electric drill
1/2" masonry bit and, if installed with lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
A drive socket and power tool for installation of the lag bolts
The flexible design of the Easy Rider® Speed Bump allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete. 
 
Installations Instructions for Asphalt: Installation of Easy Rider® Speed Bumps with spikes
(ideal for permanent speed bump installation)
 
Step 1. 
Drill 1/2" diameter holes (3 - 4" in depth) in the asphalt through the product's holes.
 
Step 2:
Drive 1/2" rebar spike (14" long) through the holes in the product. 
 
Installation Instructions for Concrete: Installation of Easy Rider® Speed Bumps with lag bolts and metal shields
(ideal for temporary installation or if removal of speed bump is necessary)
 
Step 1. 
 Use 1/2" or 5/8 lag bolts (5 1/2" long).
 
Step 2.
Drill 1/2" diameter pilot holes (3 - 4" in depth) through the product's installation holes.
 
Step 3. 
Remove the product; re-drill the holes for the diameter and depth required by the metal shields.
 
Step 4.
Install the metal shields, re-position the product and bolt with lag bolts. 
 
Maintenance
Speed bumps require minimal maintenance. Periodically inspect the bolts and tighten if necessary.